Epox-E Glue 200gm available in 4 colours
Availability:In stock
$32.55
Epox-E-Glue is high strength epoxy adhesive mixed in an equal volume 1:1 ratio for ease of handling. The 200-gram kit has a 100-gram container of resin and a 100-gram container of hardener. The amount of part A and Part B to be mixed can be judged by eye to be nearly equal. This gives a thixotropic paste which will adhere tenaciously to nearly anything and which is also able to fill large gaps and maintain strength across them. Epox-E-Glue will adhere to most things provided proper surface preparation has been done. Some plastics and some metals require special surface preparation.
Epox-E-Glue comes in 4 colours: White, Black, Pine and Cedar. The Pine colour has been matched to Hoop Pine and the Cedar colour has been matched to the typical Western red Cedar colour.
Its features are:
- non-critical easy to use 1:1 ratio by volume – simply mix two equal scoops
- extended working life of 40 minutes
- full cure within 24 hours at temperatures above 10 deg C
- non-sagging thixotropic paste formulation easily fills large gaps
- bonds strongly to most substrates
- totally waterproof
INSTRUCTIONS:
SURFACE PREPARATION
Surfaces to be bonded must be freshly sanded with coarse-grit (40 or 60 grit) abrasive, and be free from dust dirt grease or oils.
MEASURING AND MIXING
Equal volumes of Parts A and B should be mixed thoroughly until colour is uniform. Measure out equal volumes in graduated containers, scoops, etc, or for small batches use equal-sized blobs on a mixing board. Epox-E-Glue should be used within 30-40 minutes of mixing
APPLICATION
Best results will be obtained when both mating surfaces are coated with glue. Bring both coated parts together and maintain firm contact until the glue has set and strength has developed. Generally, this will be within 24 hours, but low temperatures will retard the cure rate. Do not clamp tightly as a weak joint may result from glue starvation.
If bonding porous materials such as foams, concrete, timber end grain, etc, seal the surface by pre-coating it with Bote-Cote liquid epoxy resin. This will prevent joint starvation due to the porous substrate absorbing resin out of the adhesive.
FINISHING
Epox-E-Glue will cure to an almost invisible glue line so is suitable for clear finishes. However, it may be too opaque for use for filling larger holes etc under clear finishes. Clean up any excess glue with a scraper followed by wiping away with a solvent such as acetone. Cured Epox-E-Glue may be sanded, then painted or varnished.
SAFETY
Refer to the safety data sheet and to BoatCraft brochure “Using Bote-Cote Safely and Effectively”. Always wear disposable gloves when handling epoxy chemicals, and avoid prolonged exposure in order to minimise skin sensitization developing. Avoid contact with eyes, wash hands with hand cleaner and water after use, do not use solvents on your skin.
EPOX-E-GLUE PHYSICAL PROPERTY DATA SHEET
UNCURED MATERIALS |
|
|
Resin Viscosity |
mPas |
450,000 |
Hardener Viscosity |
mPas |
450,000 |
Mixed Viscosity |
mPas |
450,000 |
Pot Life 20°C |
Minutes |
70 |
Ratio Resin / Hardener |
v/v |
1:1 |
|
w/w |
100:92 |
CURED EPOXY GLUE |
|
|
Tensile Strength |
MPa |
48 |
Tensile Elongation |
% |
6-8 |
Tensile Modulus |
GPa |
2.6 |
Flexural Strength |
MPa |
76 |
Sherar Strength |
MPa |
16 |
Compressive Strength |
|
|
@yield |
MPa |
90 |
@ failure |
MPa |
193 |
Hardness |
Shore D |
75 |
Heat Deflection Temp |
|
|
Room Temp Cure |
°C |
50-55 |
80°C Post cure |
°C |
75-80 |